Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
Just how do you feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily available, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the brand-new one. See to it you have actually certified yourself for the job as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list need to consist of the following:
Planning for the Setup
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait until the tub has actually been made use of at the very least once as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall between the bath and also the tiling, bring about issues with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub? Write a remark directly below. We'd be glad to hear your suggestions about this blog posting. Hoping to see you back again before long. For those who appreciated our page if you please make sure you remember to share it. Thank-you for your time invested reading it.
Free Estimates Report this page